Roy and Niels

Roy and Niels

Monday, March 14, 2011

How to Produce Antiprotons

Both Roy and I work on the AD-4/ACE project at CERN where we investigate antiprotons as candidate particles for use in cancer therapy. We have about one week of beam time every year where we conduct radiobiological and dosimetric experiments at the beam line in a very interdisciplinary team consisting of physicists, radiobiologists and radiation oncologists from more than 10 universities and university hospitals.

CERN is the only place in the world, where we have a antiproton beam at sufficiently *low* energy, that is, around 100 MeV which corresponds to a range of ~10 cm in water. The LHC is not involved in the production at all. In fact, for antiproton production only a relatively small amount of the CERN complex is used. However, the production is still very cumbersome. First a high energy proton beam must be made. This happens at the Proton Synchrotron (PS), the old workhorse of CERN. It was inaugurated by our great Dane Niels Bohr in 1959.
The proton beam is accelerated up to 26 GeV, and then dumped into a target followed by a so-called magnetic horn.

Antiproton production target.


Basically, it is an air cooled iridium target. When the beam is dumped, two protons are converted into three protons and an antiproton. During the dump a powerful current is sent along the beam axis, which generates a magnetic field, keeping as many antiprotons as possible on axis. Immediately after the target there is a “lithium lens” (a Russian invention), which tries to capture even more of the very precious antiprotons. The created antiprotons have a very high energy of several GeV and are then captured by the Antiproton Decelerator (AD). It then takes more than 80 seconds for the beam to slow down. The deceleration is actually not the time consuming issue, but rather shaping the beam, making it small and narrow, so antiprotons are not lost during the deceleration process.
This is realized using stochastic cooling. Along with electron cooling (which was invented by G.I. Budker, and is widely applied), this will remove energy from the transverse movements of the antiprotons, thereby reducing the emittance of the beam.

Yesterday (while following Dag Rune Olsens twitter account) I learned that Simon van der Meer, inventor of stochastic cooling - and winner of the Nobel Prize, died on 4 March 2011.
From our last antiproton run at CERN I have a large amount of video material of technicians working at the AD, which also demonstrates antiproton production and stochastic cooling of the resulting beam. Check out the excerpt below:


And yes, of all those computers, only one of them was running windows. :)

At 1:49 you can see the AD hall. The antiproton decelerater is under that ring of concrete. Those large coils at the far end, which can be seen at 1:54, are delay coax cables which “short circuit” the AD ring across the middle.
At 2:00 you see the bullseye of the production target and at 2:20 the 26 GeV proton beam hits the target as the antiprotons are made. These are slowed down, and the oscilloscope shows how emittance is reduced by stochastic cooling. The beam is then stepwise ramped down to 126 MeV, and cooled in between those steps. Finally the 126 MeV antiproton beam is extracted.
(I plan to produce more videos about the AD-4/ACE experiments, but currently kdenlive crashes frequently and corrupts my project files. It took me almost one entire day to edit those 4 min of video.)

Here is another video which shows the construction of the antiproton production target and the collector. The white cylindrical object behind the target is the lithium lens.


http://cdsweb.cern.ch/record/1063081

This is one of the “hottest” sites at CERN. Things are designed to require minimal human intervention. Here is a very old video of how a faulty magnet had to replaced near the production target. People have to plan each step in advance before they enter the zone.

http://cdsweb.cern.ch/record/1171261

4 comments:

  1. Did you ever have a chance to look at the energy of the iridium K$\alpha_2$ line? With such energetic
    protons I doubt that there's any influence on this energy from multiple excitations in the same ion where you create the K-shell vacancy, but it might be interesting to verify this.

    Nino R. Pereira at ninorpereira at google punt com

    ReplyDelete
    Replies
    1. Not sure I understand your question, but were taking GeV beams here... way out of scale of atomic physics...

      In principle you can make antiproton in any target material, I guess the reason for why they use iridium is simply a trade-off for having high density and high melting point and retaining structural integrity of the target. I do recall vaguely that they used another material earlier such as tungsten.

      There is a little more on the issue here: http://lss.fnal.gov/cgi-bin/find_paper.pl?pbar-683

      Delete
  2. did you measure the G constant of antiproton.you will find out it is negative and will explain why universe expands at accelerated speed

    ReplyDelete
  3. how does one make 26 GigaElectronVolts???

    ReplyDelete